H600-N焊干保护UV胶 电子元件固定保护紫外线胶水 快速固化高强度粘接胶

一、产品说明：H600-N 是一种单组份半流淌紫外线固化胶，适用于多种材料粘接，推荐用于电子电路元器件粘接固定、电子线路焊点保护、线路焊点线材补强粘接及电子元器件绝缘保护，密封等；常温储存稳定，固化速度快，表层固化完全光亮不粘，固化胶膜柔韧，抗冲击性强，抗湿热及化学品优良，优越的电气特性，绝缘防水防潮防尘等。

二、化学物质类型      改性丙烯酸酯        

外观                          淡黄色透明半流体

粘度(mPa.s/25℃)    15000-25000         

密度25℃ g/cm³       1.1

三、固化性能：H600-N在空气环境下需要足够的紫外能量辐射才能够固化。固化速率和固化效果需要足够的光能量，主要是200-400nm紫外光，推荐使用365nm紫外光源。

四、固化条件:

500-1000W高压汞灯,主要波长365nm；固化条件 800mj/cm²

定位：5秒，固化30秒（具体固化依所使用的光源、胶膜厚度及被粘材料测试为准）

五、固化物性能：

热膨胀系数@ 25°C, /°C      2.5 x 10_5          

硬度（邵D）                      55-65

介电常数    1MHz              3.8          

玻璃化温度°C                    10

断裂伸长率  %                   150           

介电强度 KV/MM             16

表面电阻    Ω                    3.2x 10_14          

体积电阻 Ω.cm                  5.8x 10_14

1、 Product Description: h600-n It is a kind of one component semi flowing UV curing adhesive, which is suitable for bonding of various materials. It is recommended to be used for bonding and fixation of electronic circuit components, electronic circuit solder joint protection, line solder joint wire reinforcement and bonding, insulation protection and sealing of electronic components, etc.; it is stable in normal temperature storage, fast in curing speed, completely bright and non sticky in surface curing, flexible in curing adhesive film, strong in impact resistance, and moisture and heat resistance And excellent chemicals, superior electrical characteristics, insulation, waterproof, moisture-proof and dust-proof.

2、 Chemical substance type modified acrylate appearance light yellow transparent semi fluid

Viscosity (MPa. S / 25 ℃) 15000-25000 density 25 ℃ g / cm 3 1.1

3、 Curing performance: h600-n needs enough UV energy radiation to cure in the air environment. The curing rate and curing effect need enough light energy, mainly 200-400nm UV light, 365nm UV light is recommended.

4、 Curing conditions:

500-1000w high pressure mercury lamp, main wavelength: 365nm; curing condition: 800mJ / cm2

Positioning: 5 seconds, curing for 30 seconds (the specific curing shall be subject to the test of the light source used, the thickness of the adhesive film and the adhered material)

5、 Properties of solidified products:

Coefficient of thermal expansion @ 25 ° C, / ° C 2.5 x 10 μ 5

Hardness (Shao d) 55-65

Dielectric constant 1MHz 3.8

Glass transition temperature ° C 10

Elongation at break% 150

Dielectric strength kV / mm 16

Surface resistance Ω 3.2X 10_ Fourteen

Volume resistance Ω. Cm 5.8x 10_ Fourteen